How to easily make a track from old tires with your own hands

What are the benefits of tire trails

This is the most original way of arranging the local area. Unlike wood, rubber is more resistant to temperature extremes and moisture. Its other advantages include anti-slip coating, as well as shock absorption during movement, due to which it is more convenient to climb the slopes.

Old truck tires can be unscrewed and repainted. In terms of dimensional stability, they are not much inferior to new tires. Therefore, if you are looking for raw materials for garden paths at affordable prices, if not for free, there is no better option. In the device of low fences, delimiting several zones in the country at once, such coatings perform decorative functions. Returning to practical tasks, the first thing to note is:

• frost resistance;
• hydrophobicity;
• cushioning impacts when falling;
• easy maintenance, including the possibility of minor repairs;
• no significant costs during the installation period.

When choosing car tires, it is important to be guided by the physical properties of the products. For example, summer tires, thanks to their hard rubber, withstand 40-degree heat and grip on all surfaces. Longitudinal grooves on the tread promote high-quality drainage, so that even the simplest paths last for years. Winter tires with large sipes are more suitable for decoration. It dries faster, and in the cold, unlike concrete and wooden coatings, it almost does not slip.

Video "Garden paths from old car tires"

From this video you will learn how to make a garden path from old car tires with your own hands.

Variants

With proper handling of raw materials with oily liquids, large tires can be easily cut by hand. A sharp knife, hammer, chalk and power tools for cutting hard products will come in handy. The easiest way is to make a ladder path of 40-50 tires. It is convenient to go down along it to the reservoir, the gazebo and the summer wing. And if the building is located on a hill, this is almost the only way to get to the bus stop.

The manufacturing process includes the following steps:

1. Place clean tires on the ground from bottom to top.
2. Tamp the base of the path with a vibrating plate, and, if necessary, dig a 2-centimeter trench for each element of the path.
3. Fill the holes with broken bricks or pebbles to prevent the structure from collapsing in the wind.
4. Install handrails for safe movement with children.

An equally strong track can be laid out from rubber modules. They easily change direction and connect together like puzzles. Long paths leading to garages and outbuildings are best made from square tiles. The material lends itself well to repair, does not slip and does not deteriorate under the influence of mechanical stress.

From whole tires

If there is a playground on the site, it is not necessary to cut the tires. It is really possible to make a winding staircase from whole products that leads to a slide or to a horizontal bar.Depending on the square of the area for the fence, you will need from 40 to 60 old tires, which can later be given green, orange or red shades. Small structural elements are laid out on top, and the largest ones at the bottom of the stairs.

In winter, they are never covered with ice, and in summer they are easily cleared of debris. They dry quickly after rain, promoting safe activities in the bosom of nature. Products can be stacked horizontally or vertically. Moreover, in the first case, the holes are easily filled with soil, and in the second it is possible to organize a high-quality drain.

From ribbons

First of all, it is necessary to correctly measure and process the products. To make the rubber straighten faster, the power tool is guided along the edge, and only then the tire itself is cut. Finished strips should be nailed to pine planks and laid on cleaned soil. The optimum distance between the elements of the coating is 1 mm. The gap is needed for the full drainage of rain and melt water.

Before laying tapes on site, it is important to arrange drainage. Gravel works best for this purpose. And so that the path does not bulge up, small grooves are made at the place of installation of the bars.

Curbs

Such structures protect the paths from the growth of weeds, and the subgrade from erosion. With their help, you can not only decorate the area near the house, but also outline the boundaries of the most beautiful places on the site. The maximum project budget is 700 rubles. This is 5-7 times cheaper than installing metal and plastic tapes. Tires can be stacked vertically, and cement mortar should be used for better fixation of products.

The cut tires will produce dense bands that delimit the public and private areas of spacious areas. Most often, such fences are fastened with bolts and plates. From the supporting elements, you will need logs. So that the tree does not deteriorate under the influence of bad weather, it should be impregnated with an antifungal composition before use. As a decoration, you can use larch cuts with a diameter of 10 cm.

Decor

Painted surfaces increase the resistance of products to moisture, frost and ultraviolet light. In choosing such compositions, it is more logical to give preference to paints marked KCH-136, intended for rubber processing. They absorb up to 97% of the sun's rays and provide a perfectly smooth surface for painted parts. Due to the unique property of thixotropy, self-leveling of coatings is possible, and most importantly - thickening of paints at rest.

Complete drying of the layer occurs in a few hours. If you work at a temperature of +25 ° C, the treadmill can be used in 2-3 days. The remaining tires will serve as the basis for the hot-pressed rubber tile production. These coatings are convenient to use not only outdoors, but also in residential premises.